HeadphoneTestOnline Audio Lab
Driver Hardware Health

Driver Rattle & Distortion Test

Expose blown voice coils, buzzing diaphragms, and loose plastic casing resonance with high-energy excursion tones.

Diagnostic State
Ready for Stress Test

Ensure moderate volume before initiating high-energy excursion tones.

Driver Excursion EnergyFrequency Spectrum
Target Resonance Frequencies (Common Rattle Points)
How to identify driver failure:

Buzzing / Rattling: If a pure tone produces a raspy "bzzzz" or crackle, a hair or dust particle is touching the diaphragm, or the driver surround is coming unglued.

Plastic Casing Vibration: Hold your fingers firmly against the outer earcups. If the buzzing stops, the rattling is simply loose plastic casing rather than blown drivers.

Causes of Headphone Driver Rattle & Mechanical Buzzing

Low-frequency sound waves between 20 Hz and 80 Hz demand the highest physical displacement (excursion) from headphone diaphragms. When reproducing sub-bass at moderate volumes, the moving voice coil travels farther than at any other frequency, quickly revealing mechanical defects that remain completely hidden during normal vocal or acoustic playback.

Trapped Hair Syndrome

The #1 cause of low-bass rattling in over-ear headphones. A stray hair slips through the protective mesh and rests against the plastic Mylar diaphragm, vibrating violently whenever bass hits.

Voice Coil Rub & Fatigue

Dropping headphones or overdriving them with an amplifier can deform the voice coil cylinder or dislodge the magnet gap, causing the voice coil to physically scrape against internal magnets.

Loose Earcup Casing

A loose internal screw, broken plastic clip, or detached acoustic foam inside the driver chamber can sympathetically vibrate at specific resonant frequencies (typically 40 Hz to 90 Hz).

Step-by-Step Guide: How to Inspect & Fix Driver Buzzing

Step 1: Earpad Removal & Flashlight Inspection

Carefully twist or pull off the detachable earpad on the rattling channel. Shine a strong flashlight at an angle across the front protective acoustic grille to spot any fine hairs poking into the driver cavity.

Step 2: Gentle Debris Extraction

Use clean precision tweezers to grasp the hair and gently draw it outward. Never blow compressed air directly into the driver membrane, as high pressure can easily puncture or invert the ultra-thin polymer dome.

Step 3: Verification with 40 Hz Sine Wave

Re-attach the earpad and run our 30 Hz to 60 Hz low-bass test tone above. If the rattling buzz has vanished, your headphones are fully restored to pristine acoustic health.

Understanding Total Harmonic Distortion (THD)

Total Harmonic Distortion (THD) measures the presence of unintended harmonic frequencies produced by a transducer when fed a single pure frequency. For studio monitoring and high-fidelity consumer headphones, total harmonic distortion should remain strictly below 0.5% (and ideally below 0.1% at 1 kHz). Significant buzzing or harmonic rasping indicates severe non-linear voice-coil excursion limits.

Knowledge Base

Frequently Asked Questions

Everything you need to know about testing your headphones online.

What causes headphone drivers to rattle at low frequencies?

Rattling at 30-60 Hz is commonly caused by: 1) A loose internal screw or rattling plastic baffle in the earcup, 2) A hair that slipped through the foam pad and is resting on the moving plastic diaphragm, or 3) A deformed or detached voice coil.

How can I fix a hair trapped against the headphone driver?

For over-ear headphones, remove the earpad and carefully inspect the driver mesh with a flashlight. If a hair is visible, gently remove it using clean tweezers without puncturing the delicate plastic diaphragm.

What is Total Harmonic Distortion (THD)?

THD measures unwanted frequencies added by a speaker or headphone when attempting to reproduce a pure tone. Quality headphones maintain THD below 0.5% across most of the audible frequency range.